77 re-relays 2.6 ghz 75 w relays for broadcasting industry 20.2 .795 11.2 .441 8.9 .350 9.6 .378 11.2 .441 20.2 .795 mm inch features ?excellent high frequency characteris- tics (impedance 75 w ) frequency 900mhz 2.6ghz v.s.w.r. (max.) 1.2 1.5 insertion loss (db, max.) 0.2 0.5 isolation (db, min.) 60 30 ?surface-mount terminal type also available specifications contact coil (at 20 c, 68 f ) characteristics remarks * speci?ations will vary with foreign standards certi?ation ratings. * 1 measurement at same location as "initial breakdown voltage" section. * 2 detection current: 10ma * 3 nominal operating voltage applied to the coil, excluding contact bounce time. * 4 by resistive method, nominal voltage applied to the coil: contact carrying power: 10w, at 2.6ghz, impedance 75 w , v.s.w.r. & 1.5 * 5 half-wave pulse of sine wave: 11ms, detection time: 10?. * 6 half-wave pulse of sine wave: 6ms * 7 detection time: 10? * 8 refer to 5. conditions for operation, transport and storage mentioned in notes arrangement 1 form c contact material gold initial contact resistance max. 100m w rating contact rating 1w (at 2.6 ghz, impedance 75 w , v.s.w.r. max.1.5) 10ma 24v dc (resistive load) contact carrying power 10w (at 2.6ghz, impedance 75 w , v.s.w.r. max.1.5) max. switching voltage 30 v dc max. switching current 0.5 a dc high frequency characteristics (impedance 75 w ) v.s.w.r. max. 1.2 (to 900mhz) max. 1.5 (to 2.6ghz) insertion loss max. 0.2 (to 900mhz) max. 0.5 (to 2.6ghz) isolation min. 60db (to 900mhz) min. 30db (to 2.6ghz) expected life (min. opera- tions) mechanical (at 180 cpm) 10 6 electrical 1w, 2.6ghz, impedance 75 w , v.s.w.r. & 1.5 3 10 5 10ma 24v dc (resistive load) (at 20cpm) 3 10 5 nominal operating power 200 mw initial insulation resistance* 1 min. 100 m w (at 500 v dc) initial breakdown voltage* 2 between open contacts 500 vrms between contact and coil 1,000 vrms between contact and ground terminal 500 vrms operate time* 3 (at 20 c) max. 10ms release time (without diode)* 3 (at 20?) max. 5ms temperature rise (at 20 c)* 4 max. 60 c shock resistance functional* 5 min. 500 m/s 2 {50 g} destructive* 6 min. 1,000 m/s 2 {100 g} vibration resistance functional* 7 10 to 55 hz at double amplitude of 3 mm destructive 10 to 55 hz at double amplitude of 5 mm conditions for operation, transport and storage* 8 (not freezing and condensing at low temperature) ambient temp. ?0 c to 60 c ?0 f to 140 f humidity 5 to 85% r.h. unit weight approx. 5 g .18 oz typical applications broadcasting market ?set top box (cs/bs tuner, catv tuner) ?multi-function tv ?measuring instruments for broadcasting ordering information ex. contact arrangement operating function 1: 1 form c 3: single side stable type terminal shape nil: a: standard pc board terminal surface-mount terminal coil voltage (dc) 03: 3 v 4h: 4.5 v 06: 6 v 09: 9 v 12: 12 v 24: 24 v packing style nil: z: carton (pc board terminal) tube (surface-mount terminal) tape and reel packing (picked from 1/7 pin side) are 1 3 note: tape and reel packing symbol ?z?is not marked on the relay. ? type tape and reel packing (picked from 8/9/10/11/12/13/14-pin side) is also availabe. suffix ??instead of ?? re.fm 77 y [ w qooqnr pq@?j@ ?s pxa
re 78 types and coil data (at 20 c 68 f ) ?packing of standard pc board terminal: 50 pcs. in an inner package (carton); 500 pcs. in an outer package ?packing of surface-mount terminal: 25 pcs. in an inner package (tube); 200 pcs. in an outer package 400 pcs. in an inner package (tape and reel); 800 pcs. in an outer package standard pc board terminal surface-mount terminal nominal voltage, v dc pick-up voltage, v dc (max.) (initial) drop-out voltage, v dc (min.)(initial) coil resistance, w ( 10%) nominal operating current, ma ( 10%) nominal oper- ating power, mw max. allowable voltage, v dc are1303 ARE13A03 3 2.25 0.3 45 66.7 200 3.3 are134h are13a4h 4.5 3.375 0.45 101 44.4 200 4.95 are1306 are13a06 6 4.5 0.6 180 33.3 200 6.6 are1309 are13a09 9 6.75 0.9 405 22.2 200 9.9 are1312 are13a12 12 9 1.2 720 16.7 200 13.2 are1324 are13a24 24 18 2.4 2,880 8.3 200 26.4 dimensions mm inch 1. standard pc board terminal general tolerance: 0.3 .012 2.54 .100 0.5 .020 (2.09) (.082) 7.62 .300 (1.49) ( .059 ) stand off 11.2 .441 8.6 .339 0.3 .012 3.0 .118 0.3 .012 0.3 .012 20.2 .795 schematic (bottom view) (deenergized condition) nc direction indication com no 8 9 10 11 12 13 14 7 1 2. surface mount terminal general tolerance: 0.3 .012 20.2 .795 2.54 .100 0.5 .020 (2.09) (.082) 7.62 .300 (1.49) (.059) 11.2 .441 (0.7) (.028) (1.3) (.511) 8.6 .339 0.3 .012 9.6 .378 13.2 0.5 .520 .020 0.3 .012 0.3 .012 schematic (top view) (deenergized condition) no com nc 17 8 11 10 9 12 13 14 direction indication reference data 1. high frequency characteristics (standard pc board terminal) ?v.s.w.r. characteristics ?insertion loss characteristics ?isolation characteristics 1 1.9 2.0 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 900mhz 3ghz com-nc com-no frequency v.s.w.r. 1.0 0.1 0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 900mhz 3ghz com-nc com-no frequency insertion loss, db 100 10 0 20 30 40 50 60 70 80 90 900mhz 3ghz com-no com-nc frequency isolation, db re.fm 78 y [ w qooqnr u@ j@ ?x sqa
re 79 notes 1. coil operating power pure dc current should be applied to the coil. the wave form should be rectangular. if it includes ripple, the ripple factor should be less than 5%. however, check it with the actual circuit since the characteristics may be slightly different. 2. cleaning for automatic cleaning, the boiling meth- od is recommended. avoid ultrasonic cleaning which subjects the relays to high frequency vibrations, which may cause the contacts to stick. it is recommended that alcoholic solvents be used. 3. soldering 1) the soldering shall be performed under following condition. max. 260c 500f 10s max. 350c 662f 3s the affect of the pcb on the relay will dif- fer depending on the type of pcb used. please verify the type of pcb to be used. soldering time: within 5s 2) in case of automatic soldering, the fol- lowing conditions should be observed (surface-mount terminal) (1) position of measuring temperature (2) ir (infrared re?ow) soldering method temperature rise of relay itself may vary according to the mounting level or the heating method of re?ow equipment. therefore, please set the temperature of soldering portion of relay terminal and the top surface of the relay case not to exceed the above mentioned soldering condition. it is recommended to check the tempera- ture rise of each portion under actual mounting condition before use. 4. packing style 1) tape dimensions 2) dimensions of plastic reel 5. conditions for operation, transport and storage 1) ambient temperature, humidity, and at- mospheric pressure during usage, trans- port, and storage of the relay: (1) temperature: C40 to +60c C40 to +140f (2) humidity: 5 to 85% rh (avoid freezing and condensation.) the humidity range varies with the tem- perature. use within the range indicated in the graph below. (3) atmospheric pressure: 86 to 106 kpa temperature and humidity range for us- age, transport, and storage: 2) condensation condensation forms when there is a sud- den change in temperature under high temperature and high humidity conditions. condensation will cause deterioration of the relay insulation. 3) freezing condensation or other moisture may freeze on the relay when the temperature is lower than 0c 32f . this causes prob- lems such as sticking of movable parts or operational time lags. 4) low temperature, low humidity environ- ments the plastic becomes brittle if the relay is exposed to a low temperature, low humid- ity environment for long periods of time. b 1.0mm .039inch a: surface of pc board where relay is mounted. b: above the pc board surface. a t 1 t 2 t 3 t 4 t 5 t 1 t 3 t 4 t 5 t 2 a: b: t 2 - t 1 = 80 to 120 s t 5 - t 3 = 30 to 40 s t 4 = 170 to 190 s t 1 =150 c 302 f t 2 =160 c 320 f t 3 =183 c 361 f t 4 =245 c 473 f t 5 =270 c 518 f tape coming out direction relay polarity bar 44 0.3 1.732 .012 2.0 0.15 .079 .006 40.4 1.591 20.2 .795 1.75 .069 0.4 .016 4 .157 13.85 .545 20.0 .787 1.5 .059 1.7 .067 r0.75 .030 20.75 .817 10.6 + 0.2 - 0.3 .417 + .008 - .012 re relay 1.5 + 0.1 - 0 dia. .059 + .004 - 0 380 0.2 14.961 .008 21 0.8 dia. .827 .031 dia. 13 0.2 dia. .512 .008 dia. 2.0 0.5 .079 .020 80 0.1 3.150 .004 max. 50.5 1.988 44.4 + 0.2 - 0 1.748 + .008 - 0 (avoid condensation when used at temperatures higher than 0 c 32 f ) temperature, c f humidity, %r.h. 85 5 0 +32 +60 +140 e40 e40 tolerance range (avoid freezing when used at temperatures lower than 0 c 32 f ) for cautions for use, see relay technical information (page 48 to 76). 3 / 7 /200 2 all rights rese r v ed, ? co p y r ight matsushita elect r ic w o r k s , ltd. go to online catalog
|
